
- Home
- Roof Types
- Metal Roofs
Metal Roofs in Palm Beach & Broward County
We install 5V crimp, standing seam and mechanically seamed metal roofs, in Galvalume steel or aluminum. Metal is usually the longest-lasting roof we install. Which panel and which metal you need depends on your budget, your roof and how close you live to salt water.
100% free · No obligation
Schedule Your FREE Roof Estimate / Inspection
Full re-roof quote, a repair, or just an inspection. Pick one and we'll call to set a time.
Request Received
Thanks! We'll call you shortly to set up your free estimate. Need us sooner? Call (561) 335-3869.
Three Kinds of Metal Roof
Good, better and best. The difference is how the panels are fastened and how the seams are closed.
Almost every metal roof on a South Florida home is one of these three, and we install all three. Any of them can be made in steel or aluminum, and all of them come in painted colors. Ask us to price more than one, so you can compare them side by side.
5V Crimp
The traditional Florida metal roof, named for the five V-shaped ridges pressed into each panel. Panels are about two feet wide. They're screwed straight through the metal into the roof deck, so the screw heads show. 5V costs the least of the three. The trade-off is upkeep, because every screw is a hole that depends on a small rubber washer to stay sealed.
Standing Seam
Flat panels joined by raised seams that stand an inch or more above the roof. Each panel is held down by clips or a fastening strip hidden under the next panel, and the seams snap together. No screws go through the surface that faces the weather, so there are no washers to dry out, and the panels are free to move a little as they heat and cool.
Mechanically Seamed Standing Seam
The same hidden clips, with one more step. After the panels are set, a seaming machine runs along every seam and folds the two edges over each other, once or twice. A folded seam is tighter against wind-driven rain and harder for wind to pull open than a snapped one, and it can go on lower slopes than the other two. It takes more labor, so it costs the most.

Under the panels. Every metal roof we install goes over a Polyglass high-temperature underlayment, made for the heat that builds up under metal.
Florida-approved panels. Every panel system we install has a Florida Product Approval, which lists the wind pressures it passed in testing. We give you the approval number with your quote.
Warranty. Our 10-year workmanship warranty covers every metal roof we install, on top of the manufacturer's panel and paint warranties.
- Lifespan: 30+ years
- Relative cost: 5 out of 5
- Wind: 140+ mph, depending on the panel
- Workmanship warranty: 10 years
Why Exposed Fasteners Are the Weak Spot
A 5V roof is held on by thousands of screws, and every one of them goes through the panel.

- The washers dry out. Each screw seals with a small rubber washer under its head. Years of Florida sun harden and crack that rubber, and a cracked washer lets water follow the screw down into the deck.
- The metal moves. Metal grows in the afternoon heat and shrinks at night. A long panel shifts a little every day. That motion widens the screw holes and slowly backs the screws out.
- Every screw has to be driven just right. Too tight and the washer splits. Too loose or crooked and it never seals. With thousands of screws on one roof, a few bad ones are easy to miss.
- Screws rust before panels do. Near salt water, the screw heads are often the first thing on the roof to corrode.
5V is still a sound roof. It just needs attention: have the screws checked every few years, and have loose or worn ones replaced. Standing seam costs more because it takes those screws off the surface of the roof.
Galvalume Steel or Aluminum
The panel style is one choice. What the panel is made of is the other.
Plain steel rusts, so roofing steel always wears a protective coating. Galvanized steel is coated with zinc. Galvalume is steel coated with a blend of aluminum and zinc, which holds off rust much longer than zinc alone. When we install steel, it's Galvalume. Aluminum is a different metal altogether. It has no steel in it, so it can't rust.
| Galvalume steel | Aluminum | |
|---|---|---|
| What it is | Steel with an aluminum-zinc coating, then paint | Solid aluminum, painted |
| Rust | Resists rust well away from the coast. Cut edges, scratches and screws are where salt gets in | Doesn't rust. It still needs the right screws and flashing |
| Dents | Stiffer and harder to dent | Softer. Dents more easily under branches and foot traffic |
| Heat | Moves less as it heats and cools | Grows and shrinks about twice as much, so panels need room to move |
| Thickness | Measured in gauge. 24 gauge is thicker than 26 | Measured in inches. .032 is common on homes |
| Cost | Lower | Higher |
| Best for | Most homes away from the coast | Homes near salt water |
How Close Are You to Salt Water?
In South Florida, salt air is what shortens the life of a steel roof.
- Within about a mile of the ocean or the Intracoastal, we recommend aluminum. The closer you are, the more it matters.
- Farther inland, painted Galvalume steel in a standard color is usually all you need.
Panel makers draw their own lines, and they sit closer to the water than ours. Steel panel warranties commonly stop covering roofs within about 1,500 feet of the surf, with shorter distances for bays and marshes. Salt spray doesn't stop at 1,500 feet, and a roof is a 30-year decision, so we'd rather be careful. Before you choose, ask to see the coastal limits in the panel warranty and the paint warranty.
Near salt water, the small parts matter as much as the panels. Screws, clips and flashing have to resist corrosion and suit the panel metal, because the wrong mix of metals corrodes quickly in salt air.
How Metal Handles Storms
Strong, light and reflective. In a storm, the fastening and the seams do the work.
The Metal Roofing Alliance says metal roofs can be rated for winds of 140 mph and higher. The exact rating depends on the panel, its clips or fasteners, and the deck underneath, and it's listed in the panel's Florida Product Approval.
Wind pulls up on a roof, and it pulls hardest at the edges and corners. A 5V roof resists that pull with screws through the panel, so its strength comes down to how many screws there are and how well each one is holding. Standing seam resists it with hidden clips. Folding the seams by machine locks each panel to the next, which is why mechanically seamed panels usually carry the highest wind ratings.
Metal weighs far less than tile, so it's easy on the framing. It also reflects more of the sun's heat than dark shingles, especially in lighter colors, which can help keep the attic cooler.
Broward County is part of Florida's High Velocity Hurricane Zone, so panels there must be approved for that zone. In Palm Beach and Broward, every permitted roof has to meet the Florida Building Code wind requirements for its address.
Common Metal Roof Problems
Metal is tough, but it shows problems that other roofs hide. Here's what to watch for.
Loose or Worn Screws
On 5V and other exposed-fastener roofs, screws back out and washers crack with age. Look for screw heads standing up off the panel, rust rings around them or missing washers. Caught early, it's a routine repair.
Oil Canning
Waviness you can see in the flat part of a panel, most often in low morning or evening light. Some people call it roof canning. It's cosmetic, not a leak, and no panel maker or installer can rule it out completely. Small ribs in the panel, thicker metal and a flat deck all reduce it.
Uneven Decks Show Through
Metal shows every dip in the roof deck or framing, much more than shingles or tile, so small structure problems on an older home stand out. We check the deck and framing first and fix low spots before the panels go on.
Scratches & Cut Edges
A scratch from a tool or a shoe, or the edge where a panel was cut, is where bare steel meets the weather. Inland, Galvalume's coating protects small ones. Near salt water they're the first places to rust. Touch-up paint from the panel maker covers small marks.
Flashing & Penetrations
Leaks on metal roofs usually start where the roof meets walls, vents, skylights or AC lines. These spots need flashing made for the panel, with room for the metal to move.
Low Slopes
Panels that overlap, like 5V, need more slope than standing seam to keep wind-driven rain out of the laps. Florida code calls for a 3:12 slope (3 inches of rise per foot) unless every lap is sealed. A nearly flat porch or addition may need mechanically seamed panels, or a flat roof instead.
Before You Re-Roof
A few things worth asking about, whoever you hire.
- Ask which of the three panel types is on your quote, and whether the screws will show.
- Ask what the metal is, Galvalume steel or aluminum, and how thick. With steel, a lower gauge number means thicker metal.
- Ask to see the panel and paint warranties in writing: how the standard and premium colors differ, and any limits near the coast.
- Ask for the panel's Florida Product Approval number. It lists the tested wind pressures.
- On an older home, plan for some deck or framing repairs. Metal shows unevenness that other roofs hide.
- In an HOA? Some limit metal roofs or colors, so check first. HOA tips
What Our Customers Say
“It's a family owned business and I had a very good and positive experience from start to finish in getting my new metal roof. They were very transparent from the beginning and always did exactly what they explained…”
“This company was amazing. Very professional and clean work and I would not ever use any other roofing company ever. This is the one.”
“They took the hassle out of replacing my roof. They were extremely professional, efficient, thorough and friendly.”
Metal Roof Questions
How long does a metal roof last in Florida?
Usually 30 years or more, the longest of the roofs we install. Two things cut that short: salt air on the wrong metal, and exposed screws nobody checks. Choose the metal for your distance from the coast, and have the screws looked at if your roof has them.
Read more: Is a Metal Roof Worth It in Florida?
5V crimp or standing seam: which is better?
Standing seam, if the budget allows. It has no screws through the weather side of the roof, so there's less to maintain and less to leak. 5V costs less and is a sound roof when its screws are checked every few years. Mechanically seamed standing seam is the top of the three for wind and for low slopes.
Do metal roofs rust in Florida?
Aluminum doesn't rust. Galvalume steel resists rust well inland, but salt air goes to work on cut edges, scratches and screws. That's why we recommend aluminum within about a mile of the ocean or the Intracoastal, and painted Galvalume farther inland.
What gauge should a metal roof be?
With steel, a lower number is thicker: 24 gauge is thicker than 26. Aluminum is measured in inches, and .032 is common on homes. Thicker metal resists dents and waviness better and costs more. We install steel panels in 26 and 24 gauge. Whatever the thickness, it has to match the panel's Florida Product Approval. Ask for it in writing.
Can my HOA say no to a metal roof?
It depends on your community's rules, so ask before you sign. Florida law requires homeowners' associations to adopt hurricane protection specifications, which can cover roofs, and an HOA can't deny an application that meets its own specifications. It can still set colors and styles and require a uniform look. This is general information, not legal advice. HOA tips
Is a metal roof loud in the rain, hot in summer or a lightning risk?
No to all three. Over a solid deck and underlayment, rain on metal sounds much like rain on any other roof. The loud ones are barns and porches with no deck under the metal. Lighter colors reflect more sun than dark shingles. And a metal roof doesn't make a lightning strike more likely. If lightning does hit, metal doesn't burn.
Other Roofs to Consider
Where We Work
Palm Beach and Broward County, from Jupiter to Hollywood. Not sure we cover your street? Call and ask.
